濟南華政印務印刷書籍主要由熱熔膠綁定，使用不干膠膠順序告訴熱熔膠，熱溶膠一般控制熱熔膠的溫度在160度，和只有在適當?shù)牟僮鳒囟?，熱熔膠生產強大的附著力，只有在適宜的溫度將膠水涂在書中，書封面堅定地堅持，因此準確的溫度控制膠鍋是實現熱熔膠佳粘接的關鍵。
Jinan Huazheng printing books are mainly bound by hot-melt adhesive. The self-adhesive adhesive is used to tell the hot-melt adhesive in sequence. The hot sol generally controls the temperature of the hot-melt adhesive at 160 degrees, and the hot-melt adhesive produces strong adhesion only at the appropriate operating temperature. Only when the glue is applied to the book at the appropriate temperature, the book cover firmly adheres to it, Therefore, accurate temperature control glue pot is the key to realize good bonding of hot-melt glue.
目前有一種冷膠，可根據情況直接使用或適當加水使用。冷膠的特點是附著力強，使用方便，但干燥速度慢。以熱熔膠為例，分析其在使用過程中容易引起的紙張質量問題。
At present, there is a kind of cold glue, which can be used directly or add water appropriately according to the situation. Cold glue is characterized by strong adhesion, easy to use, but slow drying speed. Taking hot melt adhesive as an example, the paper quality problems easily caused by its use are analyzed.
濟南華政印務為了防止膠印刷書籍的外觀的頁面，打開膠現象，但也需要改變傳統的印前組裝方法，傳統的四倍到三倍，此外還注意氣候和環境因素的影響不能忽略。同樣在頁面匹配的過程中，如果頁面后的書帖沒有直接完成進入下一個流程，那么很容易掉出頁面的質量，所以書帖進入下一個流程，一定要完成。所謂整理，就是把書的半成品扎好，壓實，并裝訂好，壓實后的書背上涂上一層粘合劑，使書背牢固牢固，等書背上的粘合劑干燥后，再將書背單獨安排好，進入下一道工序。
Jinan Huazheng printing in order to prevent the appearance of the pages of glue printed books and open the glue phenomenon, but it also needs to change the traditional prepress assembly method, which is four times to three times. In addition, it also pays attention to the influence of climate and environmental factors, which can not be ignored. Similarly, in the process of page matching, if the book post behind the page is not directly completed and enters the next process, it is easy to lose the quality of the page, so the book post must be completed before entering the next process. The so-called finishing is to bind, compact and bind the semi-finished products of the book, and apply a layer of adhesive on the compacted back to make the back firm. After the adhesive on the back is dry, arrange the back separately and enter the next process.
書籍用書頁裝訂后的整理工作是整個不干膠裝訂過程中非常重要的一步。
The finishing of books after page binding is a very important step in the whole self-adhesive binding process.
The wonderful content of this article is provided by the printing of Jinan books and magazines. There are many wonderful content on this website. You can click to enter more content: http://www.bosije.com We have special customer service to answer your questions
濟南華政印務有限公司
